• ajpamc_com slide-1
  • ajpamc_com slide-2
  • ajpamc_com slide-3
  • ajpamc_com slide-4
  • ajpamc_com slide-5
  • ajpamc_com slide-6
  • ajpamc_com slide-7
  • ajpamc_com slide-8
  • ajpamc_com slide-9
  • ajpamc_com slide-10

Instructions for Authors:

 

International Journal of Engineering and Robot Technology (IJERT) is an open access, Biannual journal that provides rapid publication of articles in all areas of Engineering and Robot Technology. Engineering and Robot Technology such as Civil and Architectural Engineering, Mechanical Engineering, Electronics and Communication Engineering, Electrical and Electronics Engineering, Marine Engineering, Computer Science Engineering, Automation and Mechatronics Engineering, Material and Chemical Engineering, Environmental Engineering, Petroleum and Mining Engineering, Agriculture Engineering, Aerospace Engineering, Bio-Informatics, Bio-Statistics, Bio-Medicine, Bio-technology, Management Studies, Healthcare Management Information Technology, Micro/Nano Technology, Wireless Technology and more relevant fields. International Journal of Engineering and Robot Technology (IJERT) publishes original research work either as a Full Research Paper or as a Short Communication. It is essential that authors prepare their manuscripts according to established specifications. Failure to follow them may result in papers being delayed or rejected. Therefore, contributors are strongly encouraged to read these instructions carefully before preparing a manuscript for submission. The manuscripts should be checked carefully for grammatical errors. All papers are subjected to peer review.

Types of manuscripts
Research papers:

Papers should present new experimental studies in elaborate form that constitute a significant contribution to knowledge. Research Papers should not exceed 15 pages (in word format file).

Review articles:

Papers should bring up the most important current topics or present interpretative and critical accounts, but not simple compilation, on subjects of general interest. Review Papers should not exceed 18 pages (in word format file).

Short communications:

Papers are the one that should present new important findings in a brief form, a maximum of pages should not exceed 10 including illustrations (in word format file).

Case Studies

Papers are the one that should present new important findings in a brief form, a maximum of pages should not exceed 15 including illustrations (in word format file).

Preparation of Manuscript

The manuscript should be prepared in English using “MS Word” with 1cm margin on all sides (Top, Bottom, Left and Right side) of the page. “Times New Roman” font should be used. The font size should be of 12pt but main headings should be of 14pt with bold face capitals and subheadings should be of 12pt with bold face capitals. All plant and microorganism's scientific names should be written in italic. All research article should be typed 1.5 spaced and should have the following sections: Title page, Abstract, Key words, Introduction, Materials and methods, Results, Discussion, Conclusion, Acknowledgement and References.

Title page:

The title should appear on a separate page which should then followed by the author name and the institution name and address by indicating suitable superscripts. Title page should contain title of the paper in font size 14 with bold face capitals, names of the authors in normal face upper case with font size 12 followed by the address in normal face lower case. An asterisk (*) must be placed after the corresponding authors name as superscript whose email id, fax, telephone number can be given at the bottom left corner of the title. Corresponding author has the responsibility to ensure that all co authors are aware and approve the contents of the submitted manuscript.

Abstract:

This section should start on a new page and should detail the aim of the study, experimental approach, results and conclusion in one paragraph, not more than 150 words. Avoid abbreviation, diagram and references in the abstract. All the three categories, Review Articles, Research papers and Short Communications should have an Abstract.

Keywords:

Author(s) must give about 3-6 key words which can identify the most important subjects covered by the paper. They must be placed at the end of the abstract.

Introduction:

The Introduction should start on a new page and should clearly indicate the aim of the study, the relevant literature on the subject.

Materials and Method:

The Materials and Method Should start as a continuation to introduction on the same page. All important materials used along with their source shall be mentioned. The main methods used shall be briefly described, with references.

Results and Discussion:

This section should start on a new page and the results presented in tabular or graphical form shall be described in this section. All Tables and Figures must have a title with bold and should be given only numbers (E.g. Table No.1, 2, 3…., Figure No.1, 2, 3….). The Colour photographs must be clean originals. The results should be explained clearly in discussions.

Conclusion:

The conclusion should have relevant brief conclusion (limit of 150 words) and should reflect the importance and future scope.

Acknowledgement:

All acknowledgment should be typed in one paragraph directly preceding the reference section.

Bibliography

Bibliography to the literature cited for the manuscript should be numbered in order of appearance in the manuscript and cited in the text with superscript numbers. The bibliography number should follow the following format. Please see "Model manuscript" of this Journal webpage to get an idea.

Examples
For Journal Bibliography:

Bozickovic R, Radosevic M, Cosic I, Sokovic M, Rikalovic A. Integration of simulation and lean tools in effective production systems, Journal of Mechanical Engineering, 58(11), 2012, 642 -652.

For Book Bibliography:

Bernd Bruegge and Allen H. Dutoit. Object Oriented Software Engineering, Introduction of Software Engineering, Pearson Prentice hall Publisher, Second edition, 1985, 1-25.

Article Proofs

Page proofs are sent to the designated author through e-mail. They must be carefully checked and returned the revised manuscript within 48 hours of receipt.

Our journal (IJERT) will not provide gratis reprints or hard print.

Article Charges
  • Processing cost for one article (Review or Research) is in INR.1100 (INR) - FOR Indian author.
  • Processing cost for one article (Review or Research) is in $.50 (US Dollar) - FOR Foreign author.

NOTE

  • MAIN AUTHORS are requested to send their passport size photo (only color) along with manuscript.
  • A completed and signed Copyright Form must accompanied the submission of new manuscript (Copyright Form can be obtained from the journal web site).

 

Our group of Journals

  • www.ijrpns.com (International Journal of Research in Pharmaceutical and Nano Sciences) - Impact Factor Value - 0.879.
  • www.ajpamc.com (Asian Journal of Pharmaceutical Analysis and Medicinal Chemistry) - Impact Factor Value - 0.798.
  • www.ajpcrjournal.com (Asian Journal of Phytomedicine and Clinical Research) - Impact Factor Value - 0.612.
  • www.ajrbps.com (Asian Journal of Research in Biological and Pharmaceutical Sciences) - Impact Factor Value - 0.899.
  • www.ajrcps.com (Asian Journal of Research in Chemistry and Pharmaceutical Sciences) - Impact Factor Value - 0.899.
  • www.ajrpsb.com (Asian Journal of Research in Pharmaceutical Sciences and Biotechnology) - Impact Factor Value - 0.981.
  • www.ijmhpr.com (International Journal of Medicine and Health Profession Research). - Impact Factor Value - 0.611.
  • www.ijasrjournal.com (International Journal of Arts and Science Research). - Impact Factor Value - 0.588.
  • www.ijnar.com (International Journal of Nutrition and Agriculture Research). - Impact Factor Value - 0.571.

Recent Updates

  • Call for Articles for Upcoming Issue, 2017, Volume-4, Issue-2 (July – December).
  • Submit your Original Article at editorijerobot@gmail.com.
  • If you wish to join as Editorial / Advisory board member in our Journal, Please fill the online Application Form and if you have any queries Contact above given editor email id.

newsletter